# AI Air Quality Station — print files

**v1, not test-printed yet**

License: [CC BY 4.0](https://creativecommons.org/licenses/by/4.0/), © aimebro.

These files were modeled for the exact parts listed on the aimebro project page, using published datasheet dimensions (cited below) and ~0.3 mm slip-fit clearance per side. Screw bosses for M3×12 lid screws are included even when screws are not on the project parts list — add four M3×12 (and M2 where noted) to the build.

## Parts in this folder

| File (STL + 3MF) | What it is | Print qty | Slicer PLA 0.2 mm / 15% infill |
| --- | --- | --- | --- |
| `aq-base` | enclosure base | 1 | 52.50 g, 5h 8m 45s |
| `aq-lid` | lid (mates to the base with an inner lip + M3 screws) | 1 | 20.25 g, 2h 5m 26s |

**Slicer total (including quantities): 72.8 g PLA.** Project page estimate: PLA ~100 g / 6 h, 0.2 mm, 20% infill, 2 walls (sliced here at 15% per the pilot brief).

Slicer: PrusaSlicer 2.8.1 CLI, generic 0.4 mm nozzle, 0.2 mm layers, 15% infill, 2 perimeters, PLA at 1.24 g/cm³, 210/60 °C, 220×220 mm bed. These are estimates, not a test-print log.

Lids (except the already flipped drum-top) have the 1.6 mm lip on the bed; the slicer may warn about short bridges over vent slots and screw holes. Enable supports if those bridges fail, or print the lid lip-up if you prefer.

The PMS5003 38x21 mm inlet/outlet face is at the front window, raised to z=6.5 so it sits on four flat-top M2 standoffs (the Ø6 posts stay below the body; Plantower holes are only Ø2). The sensor sits beside the DevKitC-32E. Lid screw bosses rise to just under the lid so M3x12 screws engage ~9 mm of thread.

## Dimension sources

- Espressif **ESP32-DevKitC-32E** (DevKitC V4), 38-pin, Micro-USB: official outline 48.26×27.94 mm, USB at the 48.26 end. Pocket is 48.86×28.54×15 mm (0.3 mm clearance per side) with a 12×8 mm Micro-USB opening at the rear, aligned for a board on the floor, headers-up. [V4 dimensions PDF](https://dl.espressif.com/dl/schematics/esp32_devkitc_v4_dimensions.pdf). Espressif's get-started page confirms Micro-USB (not USB-C).
- Plantower PMS5003: 50×38×21 mm; mounting 45×33 mm, 4×Ø2 self-tapping (≤ 5 mm deep); fan inlet Ø20 mm and 12 mm outlet bank on the **38×21 face**, so 50 mm is the depth into the box. Source: 2016 datasheet hosted by Adafruit, [PDF](https://cdn-shop.adafruit.com/product-files/3686/plantower-pms5003-manual_v2-3.pdf) table “Physical Size” and drawing “Physical Size (mm)”. The front window is the full 38.6×21.3 mm inlet face, raised with the pocket to z=6.5–27.8 so the inlet stays aligned when the sensor sits on four 4.5 mm flat-top M2 standoffs. The Ø6 post body stays below the PMS (Plantower holes are only Ø2 and cannot accept a Ø6 post). M2 screws go in from above, through the sensor into the standoffs, ≤5 mm deep. Do not insert them from below.
- Adafruit SCD-41 breakout (PID 5190): 25.5×22.8×7.7 mm; sensor element 10.1×10.1×6.5 mm. [Adafruit](https://www.adafruit.com/product/5190). The SCD41 pocket is to the right of the PMS, away from the DevKitC regulator at the rear.
- 0.96" SSD1306 OLED: the project lists **UCTRONICS**, which has no published drawing (UNVERIFIED). The lid pocket is an envelope covering Waveshare 0.96 inch OLED Module 26.0×26.0 mm, display 21.74×11.18 mm ([wiki](https://www.waveshare.com/wiki/0.96inch_OLED_Module)) and Adafruit PID 326 29.2×26.7×6.2 mm, screen 26.6×19 mm ([Adafruit](https://www.adafruit.com/product/326)). The viewing window is 23×13 mm (Waveshare area plus margin; it will slightly crop a 326 screen).

## Fit results

Assembly-fit check **passed**: lid and base do not intersect at the mate pose, and the datasheet-size part solids placed in their pockets do not intersect the enclosure (intersection volume ≤ 15 mm³, allowing for tessellation).

| Check | Result |
| --- | ---: |
| aq-base+aq-lid | intersection 0.00 mm³ |
| PMS5003 in aq-base | intersection 0.00 mm³ |
| Adafruit SCD-41 in aq-base | intersection 0.00 mm³ |
| ESP32-DevKitC-32E in aq-base | intersection 0.00 mm³ |
| PMS5003 vs Adafruit SCD-41 | intersection 0.00 mm³ |
| PMS5003 vs ESP32-DevKitC-32E | intersection 0.00 mm³ |
| Adafruit SCD-41 vs ESP32-DevKitC-32E | intersection 0.00 mm³ |
| PMS standoff at (16.8,4.8) | post top z=6.50 mm, sensor underside z=6.50 |
| PMS standoff at (49.8,4.8) | post top z=6.50 mm, sensor underside z=6.50 |
| PMS standoff at (16.8,49.8) | post top z=6.50 mm, sensor underside z=6.50 |
| PMS standoff at (49.8,49.8) | post top z=6.50 mm, sensor underside z=6.50 |
| PMS body vs standoffs (no hole punches) | intersection 0.00 mm³ |
| M3x12 at aq-base (8,8) | boss z=31.60, tip z=22.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at aq-base (112,8) | boss z=31.60, tip z=22.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at aq-base (8,78) | boss z=31.60, tip z=22.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at aq-base (112,78) | boss z=31.60, tip z=22.40, engagement 9.20 mm, lid gap 0.40 mm |

Clearances used throughout: 0.3 mm per side on board pockets, 0.2–0.3 mm added to nominal screw holes (M3 clearance 3.3 mm, M3 pilot 2.6 mm, M2 pilot 1.8 mm). Walls and floors are 2.0 mm (above the 1.2 mm minimum). Micro-USB openings are 12×8 mm.

## Mesh and slice status

- `aq-base`: PASS. watertight=True, winding=True, manifold=Error.NoError, extents=[120.0, 86.0, 32.0] mm.
- `aq-lid`: PASS. watertight=True, winding=True, manifold=Error.NoError, extents=[120.0, 86.0, 4.0] mm.

## Hardware to add

- 4× M3×12 for each lid (pods: 4 per pod). Bosses now rise to 0.4 mm under the lid, so an M3×12 through the 2.4 mm lid has about 9 mm of thread engagement.
- 4× M2 self-tapping, ≤ 5 mm engagement, for the PMS5003, inserted from above through the sensor into the standoffs (Plantower / Adafruit guidance).

## Unverified parts

- UCTRONICS 0.96" SSD1306 module outline (pocket is a published-board envelope).
- Generic “Sensirion SCD41 module” search-link SKU (pocket follows Adafruit 5190).

