# Teensy / NeoTrellis Drum Machine — print files

**v1, not test-printed yet**

License: [CC BY 4.0](https://creativecommons.org/licenses/by/4.0/), © aimebro.

These files were modeled for the exact parts listed on the aimebro project page, using published datasheet dimensions (cited below) and ~0.3 mm slip-fit clearance per side. Screw bosses for M3×12 lid screws are included even when screws are not on the project parts list — add four M3×12 (and M2 where noted) to the build.

## Parts in this folder

| File (STL + 3MF) | What it is | Print qty | Slicer PLA 0.2 mm / 15% infill |
| --- | --- | --- | --- |
| `drum-base` | enclosure base | 1 | 68.07 g, 6h 50m 0s |
| `drum-top` | top panel with NeoTrellis 60.6 mm window and three pot holes; export is already face-down | 1 | 24.71 g, 2h 42m 28s |

**Slicer total (including quantities): 92.8 g PLA.** Project page estimate: PLA ~150 g / 9 h, 0.2 mm, 20% infill, 3 walls, top face-down (sliced at 15%).

Slicer: PrusaSlicer 2.8.1 CLI, generic 0.4 mm nozzle, 0.2 mm layers, 15% infill, 2 perimeters, PLA at 1.24 g/cm³, 210/60 °C, 220×220 mm bed. These are estimates, not a test-print log.

Lids (except the already flipped drum-top) have the 1.6 mm lip on the bed; the slicer may warn about short bridges over vent slots and screw holes. Enable supports if those bridges fail, or print the lid lip-up if you prefer.

The top panel STL is exported already flipped so the show face sits on the bed (project setting: print top face-down). A 0.6 mm bezel on the show face retains the 60 mm elastomer. The Teensy + official 35.56x36.83 mm Rev D shield sit on the right; the pot row is at the front and clears the stack. The front-left M3 post is intact. Lid bosses rise to just under the lid for M3x12.

## Dimension sources

- PJRC Teensy 4.1: 60.96×17.78 mm, thickness 1.57 mm, USB Micro-B at one end (~0.6 mm overhang). Official drawing [dimensions_teensy41.png](https://www.pjrc.com/teensy/dimensions_teensy41.png) via [pjrc.com/teensy/dimensions.html](https://www.pjrc.com/teensy/dimensions.html).
- PJRC Audio Adaptor Rev D: official mechanical drawing (“Audio Shield” attachment, [forum thread 35021](https://forum.pjrc.com/threads/35021-Audio-board-mechanical-drawing)) labels the shield **1.40×1.45 in (35.56×36.83 mm)**. It is a shield around the Teensy, not a 17.78 mm-wide board. The pocket is 61.56×37.43×16 mm (Teensy length × shield width, plus clearance). A tall Micro-USB / jack opening on the right wall covers the 16 mm sandwich height. Jack XY is still approximate. Store page: [pjrc.com/store/teensy3_audio.html](https://www.pjrc.com/store/teensy3_audio.html).
- Adafruit NeoTrellis 4×4 (PID 3954): PCB 60×60×4 mm, product height 60.0×60.0×7.5 mm. [Adafruit](https://www.adafruit.com/product/3954).
- Adafruit silicone elastomer 4×4 (PID 1611): 60×60×11.5 mm. [Adafruit](https://www.adafruit.com/product/1611). Underside window is 60.6×60.6 mm; the show-face bezel is 0.6 mm smaller so the pad is retained.
- 10k linear pots (3-pack SKU UNVERIFIED): panel holes are 7.3 mm, sized to a published WH148 / 16 mm carbon pot 7 mm bushing, 25 mm centres, in a front row that clears the Teensy stack.

## Fit results

Assembly-fit check **passed**: lid and base do not intersect at the mate pose, and the datasheet-size part solids placed in their pockets do not intersect the enclosure (intersection volume ≤ 15 mm³, allowing for tessellation).

| Check | Result |
| --- | ---: |
| drum-base+drum-top | intersection -0.00 mm³ |
| Teensy 4.1 in drum-base | intersection -0.00 mm³ |
| Audio Adaptor Rev D in drum-base | intersection 0.00 mm³ |
| pot [15, 22] in drum-base | intersection 0.00 mm³ |
| pot [40, 22] in drum-base | intersection 0.00 mm³ |
| pot [65, 22] in drum-base | intersection 0.00 mm³ |
| M3x12 at drum-base (8,8) | boss z=27.60, tip z=18.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at drum-base (116,8) | boss z=27.60, tip z=18.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at drum-base (8,122) | boss z=27.60, tip z=18.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at drum-base (116,122) | boss z=27.60, tip z=18.40, engagement 9.20 mm, lid gap 0.40 mm |

Clearances used throughout: 0.3 mm per side on board pockets, 0.2–0.3 mm added to nominal screw holes (M3 clearance 3.3 mm, M3 pilot 2.6 mm, M2 pilot 1.8 mm). Walls and floors are 2.0 mm (above the 1.2 mm minimum). Micro-USB openings are 12×8 mm.

## Mesh and slice status

- `drum-base`: PASS. watertight=True, winding=True, manifold=Error.NoError, extents=[124.0, 130.0, 28.0] mm.
- `drum-top`: PASS. watertight=True, winding=True, manifold=Error.NoError, extents=[124.0, 130.0, 4.0] mm.

## Hardware to add

- 4× M3×12 for each lid (pods: 4 per pod). Bosses now rise to 0.4 mm under the lid, so an M3×12 through the 2.4 mm lid has about 9 mm of thread engagement.
- 4× M2 to fasten the NeoTrellis PCB to the standoffs.
- Nuts/washers for the three pot bushings as supplied with the pot pack.

## Unverified parts

- Audio Adaptor Rev D jack XY/Z on the PJRC drawing (length and outline 35.56×36.83 mm are verified).
- Exact 10k pot pack (holes follow a WH148 7 mm bushing).

