# Trivia Buzzer Pods and Host — print files

**v1, not test-printed yet**

License: [CC BY 4.0](https://creativecommons.org/licenses/by/4.0/), © aimebro.

These files were modeled for the exact parts listed on the aimebro project page, using published datasheet dimensions (cited below) and ~0.3 mm slip-fit clearance per side. Screw bosses for M3×12 lid screws are included even when screws are not on the project parts list — add four M3×12 (and M2 where noted) to the build.

## Parts in this folder

| File (STL + 3MF) | What it is | Print qty | Slicer PLA 0.2 mm / 15% infill |
| --- | --- | --- | --- |
| `trivia-pod-base` | pod base, 24 mm-deep 60.6 mm button pocket, GX12 opening | 4 | 48.25 g, 4h 16m 5s each (×4) |
| `trivia-pod-lid` | pod bezel lid (60.6 mm opening) | 4 | 10.62 g, 1h 1m 23s each (×4) |
| `trivia-host-base` | host box base, four GX12 holes + ESP32-DevKitC-32E / Micro-USB | 1 | 54.48 g, 5h 19m 34s |
| `trivia-host-lid` | host box lid | 1 | 21.99 g, 2h 10m 3s |

**Slicer total (including quantities): 311.9 g PLA.** Project page estimate: PLA ~200 g / 12 h, 0.2 mm, 20% infill, 3 walls (sliced here at 15%).

Slicer: PrusaSlicer 2.8.1 CLI, generic 0.4 mm nozzle, 0.2 mm layers, 15% infill, 2 perimeters, PLA at 1.24 g/cm³, 210/60 °C, 220×220 mm bed. These are estimates, not a test-print log.

Lids (except the already flipped drum-top) have the 1.6 mm lip on the bed; the slicer may warn about short bridges over vent slots and screw holes. Enable supports if those bridges fail, or print the lid lip-up if you prefer.

Print four of each pod part. The pod is 88 mm so the 24 mm-deep 60.6 mm well, a 2 mm locating wall, and the corner M3 posts all fit. An 8 mm cable notch in the locating wall opens toward the +Y GX12. Lid bosses rise to just under the lid for M3x12.

## Dimension sources

- Espressif **ESP32-DevKitC-32E** (DevKitC V4) in the host, Micro-USB: official 48.26×27.94 mm, pocket 48.86×28.54×15 mm, 12×8 mm Micro-USB opening. [V4 PDF](https://dl.espressif.com/dl/schematics/esp32_devkitc_v4_dimensions.pdf).
- 60 mm LED arcade dome buttons: the project page specifies 60 mm caps and a 24 mm-deep pocket. The well is Ø60.6 mm × 24 mm with a 2 mm locating wall. A 28 mm neck / Ø28.6 mm floor hole is typical of 60 mm illuminated arcade buttons but was not confirmed from a named-SKU datasheet (UNVERIFIED).
- GX12 4-pin aviation connector: 12.2 mm panel hole (12 mm nominal + 0.2 mm). Four holes on the host front, one on each pod wall.

## Fit results

Assembly-fit check **passed**: lid and base do not intersect at the mate pose, and the datasheet-size part solids placed in their pockets do not intersect the enclosure (intersection volume ≤ 15 mm³, allowing for tessellation).

| Check | Result |
| --- | ---: |
| trivia-pod-base+trivia-pod-lid | intersection -0.00 mm³ |
| trivia-host-base+trivia-host-lid | intersection 0.00 mm³ |
| ESP32-DevKitC-32E in host in trivia-host-base | intersection -0.00 mm³ |
| pod cable notch toward GX12 | intersection 0.00 mm³ |
| M3x12 at trivia-pod-base (8,8) | boss z=25.60, tip z=16.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at trivia-pod-base (80,8) | boss z=25.60, tip z=16.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at trivia-pod-base (8,80) | boss z=25.60, tip z=16.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at trivia-pod-base (80,80) | boss z=25.60, tip z=16.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at trivia-host-base (8,8) | boss z=31.60, tip z=22.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at trivia-host-base (112,8) | boss z=31.60, tip z=22.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at trivia-host-base (8,82) | boss z=31.60, tip z=22.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at trivia-host-base (112,82) | boss z=31.60, tip z=22.40, engagement 9.20 mm, lid gap 0.40 mm |

Clearances used throughout: 0.3 mm per side on board pockets, 0.2–0.3 mm added to nominal screw holes (M3 clearance 3.3 mm, M3 pilot 2.6 mm, M2 pilot 1.8 mm). Walls and floors are 2.0 mm (above the 1.2 mm minimum). Micro-USB openings are 12×8 mm.

## Mesh and slice status

- `trivia-pod-base`: PASS. watertight=True, winding=True, manifold=Error.NoError, extents=[88.0, 88.0, 26.0] mm.
- `trivia-pod-lid`: PASS. watertight=True, winding=True, manifold=Error.NoError, extents=[88.0, 88.0, 4.0] mm.
- `trivia-host-base`: PASS. watertight=True, winding=True, manifold=Error.NoError, extents=[120.0, 90.0, 32.0] mm.
- `trivia-host-lid`: PASS. watertight=True, winding=True, manifold=Error.NoError, extents=[120.0, 90.0, 4.0] mm.

## Hardware to add

- 4× M3×12 for each lid (pods: 4 per pod). Bosses now rise to 0.4 mm under the lid, so an M3×12 through the 2.4 mm lid has about 9 mm of thread engagement.

## Unverified parts

- 60 mm arcade-button 4-pack neck / thread diameter (24 mm pocket and 60 mm cap follow the project page; 28 mm neck is typical but unverified).

