# Garage Parking Assistant — print files

**v1, not test-printed yet**

License: [CC BY 4.0](https://creativecommons.org/licenses/by/4.0/), © aimebro.

These files were modeled for the exact parts listed on the aimebro project page, using published datasheet dimensions (cited below) and ~0.3 mm slip-fit clearance per side. Screw bosses for M3×12 lid screws are included even when screws are not on the project parts list — add four M3×12 (and M2 where noted) to the build.

## Parts in this folder

| File (STL + 3MF) | What it is | Print qty | Slicer PLA 0.2 mm / 15% infill |
| --- | --- | --- | --- |
| `garage-base` | enclosure base | 1 | 39.73 g, 3h 54m 11s |
| `garage-lid` | lid (mates to the base with an inner lip + M3 screws) | 1 | 14.47 g, 1h 27m 2s |
| `garage-led-channel` | 200 mm LED-strip channel, 8 mm lap joint | 3 | 8.41 g, 48m 43s each (×3) |
| `garage-led-diffuser` | 200 mm diffuser plate for the LED channel (print in white or natural PLA) | 3 | 3.18 g, 25m 47s each (×3) |

**Slicer total (including quantities): 89.0 g PLA.** Project page estimate: PLA ~80 g / 5 h, 0.2 mm, 20% infill, 2 walls, white/natural diffuser (sliced here at 15%).

Slicer: PrusaSlicer 2.8.1 CLI, generic 0.4 mm nozzle, 0.2 mm layers, 15% infill, 2 perimeters, PLA at 1.24 g/cm³, 210/60 °C, 220×220 mm bed. These are estimates, not a test-print log.

Lids (except the already flipped drum-top) have the 1.6 mm lip on the bed; the slicer may warn about short bridges over vent slots and screw holes. Enable supports if those bridges fail, or print the lid lip-up if you prefer.

Print three channel segments and three diffusers. Nest the 8 mm lap joints; snip or tuck the unused male tab on the first segment. Assembled optical length is 600 mm. The TF-Luna window is the full 26.5 mm optical face (plus clearance) so both Ø10.5 mm lenses are clear. Lid bosses rise to just under the lid for M3x12.

## Dimension sources

- Espressif **ESP32-DevKitC-32E** (DevKitC V4), Micro-USB: official 48.26×27.94 mm, pocket 48.86×28.54×15 mm, 12×8 mm Micro-USB opening at the rear. [V4 PDF](https://dl.espressif.com/dl/schematics/esp32_devkitc_v4_dimensions.pdf).
- Benewake TF-Luna: 35×21.25×13.5 mm, official product listing [en.benewake.com/TFLuna](https://en.benewake.com/TFLuna/index.html). Optical body width 26.5 mm on the 35 mm face, two Ø10.5 mm apertures (Waveshare dimension drawing). The front window is 27.1×14.1 mm (the full 26.5 mm face plus clearance, and the 13.5 mm body height plus clearance), open, with no plastic over the lenses. Ignore the A05 datasheet table typo of 12.5 mm height.
- WS2812B 60 LED/m 10 mm strip, 36 LEDs used = 600 mm. Channel inner width 10.6 mm (10 + 2×0.3). Split into three 200 mm segments so each fits a 220 mm bed.

## Fit results

Assembly-fit check **passed**: lid and base do not intersect at the mate pose, and the datasheet-size part solids placed in their pockets do not intersect the enclosure (intersection volume ≤ 15 mm³, allowing for tessellation).

| Check | Result |
| --- | ---: |
| garage-base+garage-lid | intersection 0.00 mm³ |
| channel0+channel1 | intersection 0.00 mm³ |
| channel1+channel2 | intersection 0.00 mm³ |
| channel+diffuser | intersection 0.00 mm³ |
| TF-Luna in garage-base | intersection 0.00 mm³ |
| ESP32-DevKitC-32E in garage-base | intersection -0.00 mm³ |
| TF-Luna vs ESP32-DevKitC-32E | intersection 0.00 mm³ |
| M3x12 at garage-base (8,8) | boss z=29.60, tip z=20.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at garage-base (82,8) | boss z=29.60, tip z=20.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at garage-base (8,70) | boss z=29.60, tip z=20.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at garage-base (82,70) | boss z=29.60, tip z=20.40, engagement 9.20 mm, lid gap 0.40 mm |

Clearances used throughout: 0.3 mm per side on board pockets, 0.2–0.3 mm added to nominal screw holes (M3 clearance 3.3 mm, M3 pilot 2.6 mm, M2 pilot 1.8 mm). Walls and floors are 2.0 mm (above the 1.2 mm minimum). Micro-USB openings are 12×8 mm.

## Mesh and slice status

- `garage-base`: PASS. watertight=True, winding=True, manifold=Error.NoError, extents=[90.0, 78.0, 30.0] mm.
- `garage-lid`: PASS. watertight=True, winding=True, manifold=Error.NoError, extents=[90.0, 78.0, 4.0] mm.
- `garage-led-channel`: PASS. watertight=True, winding=True, manifold=Error.NoError, extents=[208.0, 13.8, 6.4] mm.
- `garage-led-diffuser`: PASS. watertight=True, winding=True, manifold=Error.NoError, extents=[200.0, 10.4, 1.2] mm.

## Hardware to add

- 4× M3×12 for each lid (pods: 4 per pod). Bosses now rise to 0.4 mm under the lid, so an M3×12 through the 2.4 mm lid has about 9 mm of thread engagement.

## Unverified parts

- None for the quoted ESP32 or TF-Luna outlines; both are from official drawings / product pages.

