# ToF Theremin — print files

**v1, not test-printed yet**

License: [CC BY 4.0](https://creativecommons.org/licenses/by/4.0/), © aimebro.

These files were modeled for the exact parts listed on the aimebro project page, using published datasheet dimensions (cited below) and ~0.3 mm slip-fit clearance per side. Screw bosses for M3×12 lid screws are included even when screws are not on the project parts list — add four M3×12 (and M2 where noted) to the build.

## Parts in this folder

| File (STL + 3MF) | What it is | Print qty | Slicer PLA 0.2 mm / 15% infill |
| --- | --- | --- | --- |
| `theremin-base` | enclosure base | 1 | 49.24 g, 4h 42m 45s |
| `theremin-lid` | lid (mates to the base with an inner lip + M3 screws) | 1 | 14.51 g, 1h 23m 58s |

**Slicer total (including quantities): 63.8 g PLA.** Project page estimate: PLA ~60 g / 4 h, 0.2 mm, 15% infill, 2 walls.

Slicer: PrusaSlicer 2.8.1 CLI, generic 0.4 mm nozzle, 0.2 mm layers, 15% infill, 2 perimeters, PLA at 1.24 g/cm³, 210/60 °C, 220×220 mm bed. These are estimates, not a test-print log.

Lids (except the already flipped drum-top) have the 1.6 mm lip on the bed; the slicer may warn about short bridges over vent slots and screw holes. Enable supports if those bridges fail, or print the lid lip-up if you prefer.

The lid is full length. Front M3 holes sit at y≈21.1, behind the slanted front wall, so all four screws have posts and holes. Bosses rise to just under the lid for M3x12.

## Dimension sources

- Raspberry Pi Pico / Pico H: 51×21 mm, 1 mm thick, 4×Ø2.1 mm holes at 47.0×11.4 mm centres, USB Micro-B overhangs the end. Official datasheet Figure 3 (Rev 3), [PDF](https://datasheets.raspberrypi.com/pico/pico-datasheet.pdf). Pico H is the same PCB with pre-soldered headers; pocket height is 12 mm.
- VL53L1X: the project lists a generic module (SKU UNVERIFIED). The pocket envelope uses Adafruit VL53L1X (PID 3967) 25.5×17.5×4.6 mm ([Adafruit](https://www.adafruit.com/product/3967)); a Pololu 3415 13×18 mm carrier ([Pololu](https://www.pololu.com/product/3415)) also fits. Sensor windows are Ø10 mm, uncovered, through the slanted front wall.
- The front wall tilts back 23° from vertical (~67° from the bed) so it prints without support. The lid is full length; the two front M3 holes are at y≈21.1 mm, behind the slant.

## Fit results

Assembly-fit check **passed**: lid and base do not intersect at the mate pose, and the datasheet-size part solids placed in their pockets do not intersect the enclosure (intersection volume ≤ 15 mm³, allowing for tessellation).

| Check | Result |
| --- | ---: |
| theremin-base+theremin-lid | intersection 0.00 mm³ |
| Raspberry Pi Pico H in theremin-base | intersection -0.00 mm³ |
| VL53L1X (Adafruit 3967 envelope) in theremin-base | intersection 0.00 mm³ |
| VL53L1X (Adafruit 3967 envelope, right) in theremin-base | intersection 0.00 mm³ |
| Raspberry Pi Pico H vs VL53L1X (Adafruit 3967 envelope) | intersection 0.00 mm³ |
| Raspberry Pi Pico H vs VL53L1X (Adafruit 3967 envelope, right) | intersection 0.00 mm³ |
| VL53L1X (Adafruit 3967 envelope) vs VL53L1X (Adafruit 3967 envelope, right) | intersection 0.00 mm³ |
| M3x12 at theremin-base (8,21.13) | boss z=37.60, tip z=28.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at theremin-base (92,21.13) | boss z=37.60, tip z=28.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at theremin-base (8,62) | boss z=37.60, tip z=28.40, engagement 9.20 mm, lid gap 0.40 mm |
| M3x12 at theremin-base (92,62) | boss z=37.60, tip z=28.40, engagement 9.20 mm, lid gap 0.40 mm |

Clearances used throughout: 0.3 mm per side on board pockets, 0.2–0.3 mm added to nominal screw holes (M3 clearance 3.3 mm, M3 pilot 2.6 mm, M2 pilot 1.8 mm). Walls and floors are 2.0 mm (above the 1.2 mm minimum). Micro-USB openings are 12×8 mm.

## Mesh and slice status

- `theremin-base`: PASS. watertight=True, winding=True, manifold=Error.NoError, extents=[100.0, 70.0, 38.0] mm.
- `theremin-lid`: PASS. watertight=True, winding=True, manifold=Error.NoError, extents=[100.0, 70.0, 4.0] mm.

## Hardware to add

- 4× M3×12 for each lid (pods: 4 per pod). Bosses now rise to 0.4 mm under the lid, so an M3×12 through the 2.4 mm lid has about 9 mm of thread engagement.
- 4× M2 for the Pico H mounting holes (Ø2.1 mm official).

## Unverified parts

- Exact VL53L1X breakout SKU (pocket follows Adafruit 3967; window is oversized and uncovered).

