AI1 0 1 1 0 1 0 0 1 1 0 10 1 0 0 1 1 0 1 0 1 1 0 1Ai Me Bro

Heart-rate reactive LED shirt

A heart-shaped ring of LEDs on your shirt pulses in time with your real heartbeat. A Seeed XIAO ESP32-C3 reads a COOSPO H6 Bluetooth chest strap and changes color from calm blue to racing red as your heart rate rises.

BeginnerBuild time: 4-6 hours (plus ~2 h printing)Parts: $60-1103D print
Illustration of Heart-rate reactive LED shirt
Illustration. An artist's impression, not a photo of a finished build. Your build will look different.

Safety first

  • This is a fun light show, not a medical device. Do not use it to monitor a health condition.
  • Cap brightness at about 30% so the LEDs stay cool against your body and the power bank lasts.
  • Remove all electronics before washing the shirt.
  • Keep wires short and secured so they cannot catch on anything while you move.

Parts

PartQtyApprox. eachSubtotal
COOSPO H6 Bluetooth heart rate monitor chest strapUses the standard Bluetooth LE Heart Rate Service, so any strap that does the same will work. Typical $25-40, no verified link.Amazon (search)1$30$30
Seeed Studio XIAO ESP32-C3Tiny board with Bluetooth LE and USB-C. Typical $5-9, no verified link.Amazon (search)1$6$6
BTF-LIGHTING WS2812B LED strip, 60 LED/m, 1 mAbout 30 LEDs cut into a heart outline. Typical $8-14, no verified link.Amazon (search)1$10$10
Silicone-insulated 26 AWG wire kitTypical $7-13, no verified link.Amazon (search)1$10$10
Anker PowerCore 5000 USB power bankSkip if you already own one. Any small power bank that does not auto-shut-off at low current. Typical $15-24, no verified link.Amazon (search)1$18$18
Sew-on snap fasteners and Velcro strips kitTypical $6-10, no verified link.Amazon (search)1$8$8
Black craft felt sheets (pack)Backing for the LED heart. Typical $4-8, no verified link.Amazon (search)1$6$6
Plain cotton T-shirtSkip if you already own one. Typical $5-12, no verified link.Amazon (search)1$8$8
Estimated total (parts only)$96

Typical US prices, checked 2026-11-12. Prices change and multi-packs are often cheaper per piece.

As an Amazon Associate I earn from qualifying purchases. Prices change; check the store.

Filament

PLA (1.75 mm): about 25 g (8.4 m), roughly 2 h of printing.

PLA, 0.2 mm layers, 20% infill, 2 walls; small pocket box with rounded edges.

AI agents you'll use

  • Code helper (ChatGPT, Claude, Gemini or Grok): Writes the XIAO ESP32-C3 sketch: scan for the strap, subscribe to heart-rate notifications, and drive a beat animation with FastLED.
  • Color design helper: Picks heart-rate zones and colors for your age and activity and turns them into a simple color map.

Tools

  • Soldering iron
  • Wire stripper
  • Needle and thread, or fabric glue
  • USB-C data cable

What you'll learn

  • Reading a standard Bluetooth LE heart-rate service
  • Animating LEDs from live data
  • Wearable wiring that survives movement
  • Power budgets for battery LEDs

Wear your heartbeat. At rest the heart glows a slow blue; dance, run or watch a scary movie and it speeds up and turns red. It is a crowd favorite at parties and races.

What you'll build

About 30 LEDs from a WS2812B strip, cut into short segments and soldered with flexible wire into a heart outline, sewn or snapped to the inside of a T-shirt so they glow through the fabric. A XIAO ESP32-C3 in a small pocket box connects to the chest strap over Bluetooth LE, reads beats per minute, and pulses the heart at that rate. A power bank in a pocket runs it.

The cost range is $60-110. The low end assumes you already own these items marked "skip if you already own one": Anker PowerCore 5000 USB power bank, Plain cotton T-shirt. The high end includes them.

Print the parts

Print a small rounded box for the XIAO with a cable exit. A strap clip is optional.

Wiring

From To Notes
Power bank USB XIAO USB-C XIAO 5V pin then feeds the LEDs.
XIAO 5V / GND LED strip 5V / GND Keep brightness low; 30 LEDs at 30% draw well under 1 A.
XIAO D10 (GPIO10) LED strip DIN Short wire. Add a 330 ohm resistor in series if it flickers.

Step-by-step

  1. Pair-test: flash a BLE scan sketch and check the strap shows up when worn (it needs skin contact to start).
  2. Subscribe to the Heart Rate Measurement characteristic and print BPM.
  3. Cut the strip into short segments and wire them into a heart outline on a piece of felt.
  4. Write the beat animation and the color map from the helper.
  5. Attach the felt heart inside the shirt with snaps or Velcro, and the box in a pocket.
  6. Test while walking, then jogging.

Code

Arduino-ESP32 for the XIAO ESP32-C3 with NimBLE-Arduino (BLE client) and FastLED.

Prompt for the code helper:

Write an Arduino sketch for a Seeed XIAO ESP32-C3 using NimBLE-Arduino: scan for a device advertising the Heart Rate Service (0x180D), connect, and subscribe to Heart Rate Measurement (0x2A37); parse the flags byte to read 8- or 16-bit BPM.
Drive 30 WS2812B on GPIO10 with FastLED at max brightness 76: pulse the whole heart once per beat, colored blue under 90 BPM, purple 90-130, red above 130. Reconnect automatically, and show a slow breathing white if no strap is connected.

Troubleshooting

  • Strap never appears: It only advertises when worn with damp electrodes. Wet the pads and wear it.
  • Heart pulses irregularly: Use the BPM value to time the pulse rather than waiting for each notification.
  • Power bank turns off: Its low-current auto-off triggers. Use a bank with an always-on mode.

Last checked 2026-11-12. Double-check parts against your own board and seller listings before you buy.

Heart-rate reactive LED shirt: parts, filament and AI agents | Ai Me Bro