AI1 0 1 1 0 1 0 0 1 1 0 10 1 0 0 1 1 0 1 0 1 1 0 1Ai Me Bro

16-step drum machine with an AI beat helper

A standalone drum machine: a lit 4x4 NeoTrellis pad grid programs 16-step patterns, a Teensy 4.1 plays drum samples from its SD card through the PJRC audio adaptor, and three knobs set tempo, swing and volume. An AI helper turns "boom-bap at 90 BPM" into patterns you load.

IntermediateBuild time: 8-12 hours (plus ~9 h printing)Parts: $75-1253D print
Illustration of 16-step drum machine with an AI beat helper
Illustration. An artist's impression, not a photo of a finished build. Your build will look different.

Safety first

  • Start with the volume low before putting on headphones; sudden loud transients can hurt your hearing.
  • Only use drum samples you made or have a license to use.

Rules and laws

  • Sample packs come with licenses. Check that yours allow use in your own music, especially if you publish it.

Parts

PartQtyApprox. eachSubtotal
PJRC Teensy 4.1Has a built-in microSD slot for samples. Solder pins before mounting the audio board. Typical $30-36, no verified link.Amazon (search)1$31.50$31.50
PJRC Teensy Audio Adaptor Rev DRev D matches Teensy 4.x pinout. Typical $13-17, no verified link.Amazon (search)1$13.75$13.75
Adafruit NeoTrellis RGB driver PCB for 4x4 keypadPrice seen $12.50 on Adafruit (Nov 12, 2026).Adafruit1$12.50$12.50
Adafruit silicone elastomer 4x4 button keypadPrice seen $4.95 on Adafruit (Nov 12, 2026). Fits the NeoTrellis PCB.Adafruit1$4.95$4.95
10k linear potentiometer with knob (pack)Typical $6-11, no verified link.Amazon (search)1$8$8
SanDisk Ultra 32GB microSD cardTypical $7-12, no verified link.Amazon (search)1$10$10
Male header pins (break-away, pack)Typical $4-8, no verified link.Amazon (search)1$6$6
Creative Pebble USB speakersSkip if you already own one. Any powered speaker or headphones on the 3.5 mm jack work. Typical $20-30, no verified link.Amazon (search)1$25$25
Estimated total (parts only)$111.70

Typical US prices, checked 2026-11-12. Prices change and multi-packs are often cheaper per piece.

As an Amazon Associate I earn from qualifying purchases. Prices change; check the store.

Filament

PLA (1.75 mm): about 93 g (31.2 m), roughly 9.5 h of printing.

PLA, 0.2 mm layers, 15% infill, 2 walls (the settings the v1 files were sliced with); print the top panel face-down for a smooth surface.

AI agents you'll use

  • Code helper (ChatGPT, Claude, Gemini or Grok): Writes the Teensy sketch: NeoTrellis input, 16-step sequencer with swing, and Teensy Audio Library sample playback from the SD card.
  • Beat helper: Turns a style description into 16-step patterns for kick, snare, closed hat and open hat as arrays you paste into a file on the SD card.

Tools

  • Soldering iron
  • Wire stripper
  • Small screwdriver
  • USB micro-B data cable
  • Headphones or a powered speaker

What you'll learn

  • Sample playback with the Teensy Audio Library
  • Step sequencers and swing timing
  • I2C keypads with RGB feedback
  • Turning text ideas into drum patterns

Tap in a beat on glowing pads and hear it loop instantly, no laptop needed. The AI helper is your producer friend: describe a groove and it hands you a pattern to start from.

What you'll build

A desk box about 15 x 12 cm. The 4x4 NeoTrellis is the step grid: each pad is one of 16 steps for the selected drum, lit when active, with a moving light showing the playhead. The Teensy 4.1 plays WAV samples from microSD through the audio adaptor's headphone/line output. Three knobs set tempo, swing and volume; holding a pad combination switches drum tracks and saves patterns to SD.

The cost range is $75-125. The low end assumes you already own these items marked "skip if you already own one": Creative Pebble USB speakers. The high end includes them.

Print the parts

Print a top panel with a 4x4 cut-out matching the elastomer keypad and three knob holes, plus a base. Adafruit's NeoTrellis guide has dimensions. Credit any designer you remix.

Wiring

From To Notes
Audio Adaptor Rev D Stacked on Teensy 4.1 with headers Uses I2S and I2C pins; follow PJRC's pin table.
NeoTrellis VIN / GND Teensy 3.3V / GND
NeoTrellis SDA / SCL Teensy pins 18 / 19 Shared with the audio codec control bus (different address).
Potentiometers (3) Teensy 3.3V, GND and pins A14, A15, A16 (pins 38, 39, 40) Check these are free with the audio board fitted.
Headphones or speaker Audio adaptor 3.5 mm jack

Step-by-step

  1. Solder headers and stack the audio adaptor on the Teensy 4.1.
  2. Run PJRC's WAV-player example from the SD card to confirm audio works.
  3. Wire the NeoTrellis and run Adafruit's NeoTrellis example.
  4. Write the sequencer with the AI helper: grid input, playhead, four drum tracks.
  5. Add the knobs for tempo, swing and volume.
  6. Ask the beat helper for a few patterns and load them from SD.
  7. Print the enclosure and mount everything.

Code

Arduino IDE with Teensyduino, the Teensy Audio Library and the Adafruit seesaw library for the NeoTrellis.

Prompt for the code helper:

Write a Teensyduino sketch for a Teensy 4.1 + Audio Adaptor Rev D drum machine.
Inputs: Adafruit NeoTrellis 4x4 on I2C (pins 18/19), pots on A14 (tempo 60-180 BPM), A15 (swing 0-60%), A16 (volume).
Four tracks (kick, snare, closed hat, open hat) of 16 steps; WAV samples KICK.WAV etc. on the built-in SD card played with AudioPlaySdWav objects into a mixer. Light active steps per track, show the playhead, and load/save patterns from PATTERNS.TXT.
Use the Audio System Design Tool object names from the official PJRC library.

Troubleshooting

  • Clicks or dropouts: Too many simultaneous SD reads. Use short samples or load them into memory with the library's memory player.
  • No sound: Check the audio adaptor is Rev D and the sgtl5000 is enabled with a volume above zero.
  • Pads do not respond: NeoTrellis address or wiring; run the Adafruit example first.

Print files

Files, code and docs

Last checked 2026-11-12. Double-check parts against your own board and seller listings before you buy.

16-step drum machine with an AI beat helper: parts, filament and AI agents | Ai Me Bro