Robots projects
BeginnerRobots3D printDesktop color-sorting robot for candy and beads
A printed hopper feeds one piece at a time past a TCS34725 color sensor, then a second SG90 servo swings a chute to drop it into the right cup. An Arduino UNO runs it, and an AI helper writes and tunes the color thresholds.
$50-70 · 4-6 hours (plus ~14 h printing)
AdvancedRobots3D printHexapod walking robot with 18 servos
A six-legged printed walker with three MG90S servos per leg, two PCA9685 servo boards, an MPU-6050 and an ESP32 that runs a tripod gait you write with an AI helper. Powered by two 18650 cells through a rocker switch and two buck converters.
$175-285 · 15-25 hours (plus ~22 h printing)
BeginnerRobots3D printLine-following robot car
A two-wheel robot that follows a strip of black tape using inexpensive IR sensors and a short control loop. A classic first mobile-robot build, with an AI helper writing the firmware.
$35-60 · 4-6 hours, plus about 6 hours of printing if you print the chassis
IntermediateRobots3D printMini sumo robot (10 cm, 500 g class)
A 10 x 10 cm autonomous sumo bot with two N20 gear motors, a DRV8833 driver, two VL53L0X time-of-flight sensors to find the opponent and two TCRT5000 sensors to stay inside the ring. An Arduino Nano runs it on a 2S LiPo.
$100-215 · 8-12 hours (plus ~5 h printing)
BeginnerRobots3D printObstacle-avoiding rover
A small rover that rolls forward until an ultrasonic sensor sees something in the way, then backs up and turns. A friendly second mobile-robot project, with an AI helper writing the behavior loop.
$35-60 · 4-7 hours, plus about 7 hours of printing if you print the chassis
AdvancedRobots3D printRobot dog with 12 servos
A printed four-legged robot dog using Deok-yeon Kim's original SpotMicro frame: 12 JX PDI-HV5523MG high-voltage servos (three per leg), a PCA9685 servo board, an MPU-6050 for balance and an ESP32 brain, powered by a 2S LiPo.
$380-560 · 25-40 hours (plus ~45 h printing)
IntermediateRobots3D printRobotic hand that copies your glove
Bend your fingers in a glove fitted with five flex sensors and a printed five-finger hand copies you. One ESP32 reads the glove and sends the bends over ESP-NOW; a second ESP32 drives five MG90S servos that pull the fingers with fishing-line tendons.
$130-190 · 10-16 hours (plus ~18 h printing)
AdvancedRobots3D printSelf-balancing two-wheel robot
A narrow two-wheel robot that uses an MPU6050 inertial sensor and a fast control loop to stay upright. Most of the work is mechanical alignment and patient PID tuning, with an AI helper reading your logs.
$55-95 · 8-14 hours, plus about 7 hours of printing
BeginnerRobots3D printTiny ESP32 desk robot with an OLED face
A palm-sized desk buddy with animated eyes on a 0.96-inch OLED that turns its head and waves with two micro servos. A beginner evening build where an AI helper writes and debugs the code with you.
$30-50 · 4-6 hours, plus about 5 hours of printing
IntermediateRobots3D printVoice-controlled 4-DOF robot arm
A printed desktop arm with four SG90 servos that waves, homes, and grips when you say a short command. An ESP32 moves the joints; a computer running Whisper turns speech into serial orders.
$50-85 · 6-10 hours, plus about 10 hours of printing
Every project lists the parts, filament, AI agents and safety notes we checked on the date shown. Pictures are illustrations, not photos of a finished build. Spot a mistake? Tell us on the boards.