Drones and RC projects
IntermediateDrones and RC3D print3-inch FPV drone with Betaflight
A 3-inch freestyle or cinewhoop-style FPV quad you assemble, flash with official Betaflight, and fly in a legal open area. The frame is carbon; you may print TPU pads and a camera bumper.
$250-645 · 8-12 hours, plus about 2 hours of printing for TPU pads
AdvancedDrones and RC3D printDrone follow-me tracker
A companion computer and camera on an ArduPilot aircraft that tries to keep you in the frame and send follow or guidance commands over MAVLink. This is an add-on to a capable, legal GPS quad, not a first drone.
$475-755 · 12-20 hours on top of an already flying ArduPilot craft
IntermediateDrones and RC3D printFixed-wing foam glider with iNav
A foam-board or EPO wing with a small brushless motor, a couple of servos, a GPS, and official iNav on a wing flight controller. It cruises, holds a heading, and can return home when you set it up carefully.
$150-335 · 8-14 hours, plus about 2 hours if you print a motor mount or horns
AdvancedDrones and RC3D printGPS autopilot airboat with ArduPilot
A foam twin-hull airboat pushed by two guarded air propellers, steered by differential thrust, and run by ArduPilot Rover on a Matek H743 board with an M10 GPS and compass. Drive it by radio, then let it follow a waypoint mission across a pond and come home.
$240-465 · 12-20 hours (plus ~8 h printing)
AdvancedDrones and RCIndoor mini light-show swarm with 3 Crazyflies
Three palm-sized Crazyflie 2.1+ quadcopters, each with a Flow deck v2 to hold position and a top-mounted Color LED deck, fly a short choreographed light show from a Python script on your laptop through one Crazyradio 2.0.
$995-1025 · 6-10 hours (mostly software), no printing required
IntermediateDrones and RC3D printIndoor tiny whoop drone
A 65 mm or 75 mm ducted micro quad you can fly in a gym or a large indoor space, running official Betaflight on a 1S or 2S AIO board. Light, fragile, and still not a living-room toy until you can disarm instantly.
$130-300 · 4-8 hours, plus about 1 hour if you print a canopy
AdvancedDrones and RC3D printMapping drone with ArduPilot
A GPS-guided quad or small airframe running official ArduPilot, planned in Mission Planner (or QGroundControl), that flies a grid and takes photos for a map. This is a heavier, more serious aircraft than a 3-inch freestyle quad.
$445-810 · 15-25 hours, plus a few hours if you print mounts
IntermediateDrones and RC3D printSelf-driving RC car with Donkey Car
Turn a WLtoys 144010 1/14 RC car into a self-driving racer: a Raspberry Pi 5 with a wide-angle camera records you driving laps, trains a neural network, then drives the track by itself using the open-source Donkey Car software.
$315-390 · 8-14 hours (plus ~12 h printing and training time)
IntermediateDrones and RC3D printTethered mini underwater ROV with a live camera
A PVC-frame underwater robot with three 12 V bilge-pump motors as thrusters (two to drive and turn, one to dive) and a waterproof USB endoscope camera. All electronics and the battery stay dry on the surface, connected by a 10 m tether.
$255-340 · 10-16 hours (plus ~7 h printing)
Every project lists the parts, filament, AI agents and safety notes we checked on the date shown. Pictures are illustrations, not photos of a finished build. Spot a mistake? Tell us on the boards.